View CM2400-02TR_611063.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRELIMINARY CM2400-02/03/04 Universal Serial Bus Transceiver with Level Translator
Features
* * * * * * * * * * * * Complies with USB Specification Rev 1.1 & 2.0 Supports full speed (12Mbit/sec.) and low speed (1.5Mbits/sec.) modes Integrated 5V to 3.3V regulator Used as a USB device transceiver or host transceiver VBUS disconnection indication through VP and VM outputs Two single-ended receivers with hysteresis USB Detection of VBUS via level translator Stable RCV output during SE0 condition Low power operation from VCC Supports 1.65V to 3.6V I/O voltage levels Full industrial operating range -40 to 85 C Available in small HBCC-16 and TSSOP-16 packages
Product Description
The CM2400-02/03/04 Universal Serial Bus (USB) transceiver is fully compliant with the USB specification Rev 1.1 and 2.0. It supports a speed of 12Mbits/s (Full Speed Mode). An internal level shifter allows interface to Application Specific ICs (ASICs) and Programmable Logic Devices (PLD's) running at core voltages of 1.65V to 3.6V. The CM2400-02/03/04 features an internal 5V to 3.3V regulator which is used to power the USB transceiver via the USB supply VBUS. The CM2400-04 features a Mode Input pin (MODE) which allows the device to operate in either single or differential input mode. This device is ideal for portable electronic devices such as mobile phones, digital still cameras, PDAs (Personal Digital Assistants) and IAs (Information Appliances). The CM2400-02/03/04 is packaged in a small form-factor 16-lead HBCC or TSSOP package to conserve board space.
Applications
* * * * Wireless handsets Digital still cameras PDAs (Personal Digital Assistants) IAs (Information Appliances)
Simplified Block Schematic
Voltage Regulator VCC VREG VPU ENUM OE VMO/FSEO VPO/VO SPND RCV SPEED MODE*
VBUS
LEVEL TRANSLATOR
D+ D-
VP VM GND
* MODE pin available on CM2400-04 only.
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
1
PRELIMINARY CM2400-02/03/04
PACKAGE / PINOUT DIAGRAM
SPEED VPU ENUM OE RCV VP VM SPND GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
VBUS VREG VMO/FSEO VPO/VO D+ DSPEED VCC OE
1
SPND VM VP RCV
5
6
7
8
9
DD+ VPO/VO VMO/FSEO VREG
SPEED
MODE
GND
VCC
VCC
SPND VM VP RCV OE
5
6
7
8
9
DD+ VPO/VO VMO/FSEO VREG
4 3 2
HBCC-16
10 11 12
4 3 2
HBCC-16
10 11 12
GND
17
GND
17
16
15 14
13
1
16
15 14
13
ENUM
ENUM
VPU
VBUS
VPU
CM2400-02TS/-03TS Top View
Note: These drawings are not to scale.
CM2400-02HB/-03HB Bottom View
CM2400-04HB Bottom View
PIN DESCRIPTIONS
HBCC-16 PINS 1 2 3 4 5 6 TSSOP-16 PINS 3 4 5 6 7 8 NAME OE RCV VP VM SPND MODE GND 7 8 9 10 9 10 11 12 VCC SPEED DD+ DESCRIPTION Input for Output Enable (Active low). Enables transceiver driver to transmit data on the USB bus. When OE pin = LOW, driver circuitry is enabled. Differential receiver output of D+ and D- input data lines. The output state of RCV is preserved and stable during an SE0 condition. Single-ended D+ receiver output for detection of a single-ended zero or error conditions Single-ended D- receiver output for detection of a single-ended zero or error conditions. Suspend input. Allows the device to enter a low power state while the USB is inactive. Mode input (CM2400-04). Selects between differential (VPO, VMO) and singleended mode (VO, FSEO). Ground input (CM2400-02/03). Supply voltage for digital I/O pins. Voltages supported: 1.65 to 3.6V. Speed Input. If SPEED is logic '1', selects full speed. If SPEED is logic '0', selects low speed. SPEED changes slope rise and fall time on D+ and D-. Negative USB data connection. Positive USB data connection. In full-speed connect mode, connect to VPU via a 1.5k resistor. Tolerance of this resistor is defined in the USB specification REV 1.1 & 2.0 Driver data input. Driver data input. Regulated supply voltage output during USB operation of VBUS. 1F decoupling capacitor is required. Supply voltage input. Can be directly connected to USB VBUS. Pull-up supply voltage. Pin function is controlled by input ENUM.
11 12 13 14 15
13 14 15 16 1
VPO/VO VMO/FSEO VREG VBUS VPU
(c) 2004 California Micro Devices Corp. All rights reserved.
2
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
VBUS
08/24/04
PRELIMINARY CM2400-02/03/04
PIN DESCRIPTIONS (CONT'D)
16 2 ENUM Enumerate, allows software to control connection of the external pull-up via the level translator. If ENUM = LOW then VPU is floating. If ENUM = HIGH then VPU is internally connected to VREG. The ground terminal is connected to the exposed diepad (heatsink).
17
-
GND
Ordering Information
PART NUMBERING INFORMATION
PADS/ LEADS 16 16 16 16 16 Standard FInishing Package HBCC-16 TSSOP-16 HBCC-16 TSSOP-16 HBCC-16 Ordering Part Number1 CM2400-02HB CM2400-02TS CM2400-03HB CM2400-03TS CM2400-04HB Part Marking CM240002HB CM240002TS CM240003HB CM240003TS CM240004HB Lead-free FInishing2 Ordering Part Number1 CM2400-02HA CM2400-02TR CM2400-03HA CM2400-03TR CM2400-04HA Part Marking CM240002HA CM240002TR CM240003HA CM240003TR CM240004HA
Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. Note 2: Lead-free, 100% tin plated.
Specifications
ABSOLUTE MAXIMUM RATINGS
PARAMETER ESD Protection (All Pins except D+/D- pins, HBM, See Note 1) ESD Protection (D+/D- pins, HBM, See Note 1) VBUS VCC VI (INPUT) Storage Temperature Range Operating Temperature Range Junction RATING +1000 +4000 [GND - 0.5] to +5.5 [GND - 0.5] to +6.0 [GND - 0.5] to [VCC + 0.5] -65 to +150 -40 to +150 UNITS V V V V V C C
Note 1: Equivalent to discharging a 100pF capacitor via a 1.5k resistor (Human body model).
STANDARD (RECOMMENDED) OPERATING CONDITIONS
SYMBOL VBUS VCC VI VI(AI/O) TA PARAMETER USB VBUS Supply DC System Supply DC Input Voltage Analog I/O Pins (D+, D-) Ambient Operating Temperature Range MIN 4.0 1.65 0 0 -40 TYP 5.0 3.3 MAX 5.5 3.6 VCC 3.6 +85 UNITS V V V V C
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
3
PRELIMINARY CM2400-02/03/04
Specifications (cont'd)
ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE 1)
Supply Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V) SYMBOL VREG IBUS IBUS(IDLE) IBUS(DIS) ICC ICC(STAT) PARAMETER Regulated supply output Operating supply current Supply current during full speed idle and SE0 Disable mode supply current CONDITIONS Unloaded Full-speed TX and RX; CL=50pF on D+/D- outputs; Note 2 Full-speed idle; Notes 3 & 4 VCC not present; Note 4 SPND = HIGH; Notes 3 & 4 Full-speed TX and RX; Note 5 Full-speed idle, SE0 or suspend; Note 5 MIN 3.0 TYP 3.3 MAX 3.6 8 500 60 60 1.0 1.0 1.0 1.0 0.8 2.4 0.5 1.4 MIN 1.2 IOL = 100A IOL = 2mA IOH = 100A IOH = 2mA 1.50 1.25 0.15 0.40 TYP MAX 0.5 UNITS V mA A A A mA A A A V V V V UNITS V V V V V V
IBUS(SUSP) Suspend mode supply current Operating I/O supply current Static I/O supply current
ICC(SHARE) Supply current during sharing mode VBUS not connected; Note 5 IDX(SHARE) D+/D- load current during sharing mode VTH(VBUS) VTH(VCC) VBUS supply detection threshold VCC supply detection threshold VBUS not connected; ENUMERATE = LOW; Note 5 Supply lost Supply present Supply lost (USB_D low) Supply present Digital Pins (VBUS = 4.0V to 5.5V; VCC = 1.8V 0.15V) SYMBOL VIL VIH VOL VOH PARAMETER Logic LOW input voltage Logic HIGH input voltage Logic LOW output voltage Logic HIGH output voltage CONDITIONS
Note 1: Note 2: Note 3: Note 4: Note 5:
Operating Characteristics are over Standard Operating Conditions unless otherwise specified. Equivalent to discharging a 100pF capacitor via a 1.5k resistor (Human body model). Excluding any load current and VPU/VSW source current to 1.5k and 15k pull-up and pull-down resistors (200 A). Current is drawn from VBUS of Host when device is a peripheral. Low current ideal for battery powered applications.
(c) 2004 California Micro Devices Corp. All rights reserved.
4
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
08/24/04
PRELIMINARY CM2400-02/03/04
Specifications (cont'd)
ELECTRICAL OPERATING CHARACTERISTICS (CONT'D)
Digital Pins (VBUS = 4.0V to 5.5V; VCC = 2.5V 0.2V) SYMBOL VIL VIH VOL VOH PARAMETER Logic LOW input voltage Logic HIGH input voltage Logic LOW output voltage Logic HIGH output voltage IOL = 100A IOL = 2mA IOH = 100A IOH = 2mA CONDITIONS 2.15 1.90 1.7 0.15 0.40 CONDITIONS MIN TYP MAX 0.7 UNITS V V V V V V
Digital Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V) SYMBOL VIL VIH VOL VOH PARAMETER Logic LOW input voltage Logic HIGH input voltage Logic LOW output voltage Logic HIGH output voltage IOL = 100A IOL = 2mA IOH = 100A IOH = 2mA CONDITIONS VCC - 0.15 VCC - 0.40 MIN 0.2 0.8 2.5 0.8 2.0 0.4 RL = 1.5K tied to +3.6V RL = 15K tied to GND Pin to GND 50 Measured with steady-state drive; See Note 6 28 39 44 2.8 0.7 0.3 3.6 +1 20 TYP MAX 0.6 VCC 0.15 0.40 MIN TYP MAX 0.3 VCC UNITS V V V V V V
Analog I/O Pins (VBUS = 4.0V to 5.5V; VCC = 1.65V to 3.6V) SYMBOL VDI VCM VIL VIH VHYS VOL VOH ILZ CIN RSW ZDRV PARAMETER Differential receiver input sensitivity Differential receiver common mode voltage Single-ended receiver logic LOW input voltage Single-ended receiver logic HIGH input voltage Single-ended receiver Hysteresis voltage Logic LOW output voltage Logic HIGH output voltage OFF-state leakage current Transceiver Capacitance Internal switch resistance at VPU Driver output impedance (includes 33 ohm 1% resistor) UNITS V V V V V V V A pF
| VI(D+) - VI(D-) |
Note 6: Rev 2.0 states ZDRV must be between 28 and 44 when the driver is not high speed capable. ,
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
5
PRELIMINARY CM2400-02/03/04
Specifications (cont'd)
ELECTRICAL OPERATING CHARACTERISTICS (CONT'D)
Driver Characteristics & Timings (Full-speed mode only, SPEED=HIGH) SYMBOL tFR tFF FRFM VCRS tPLH(DRV) tPHL(DRV) tPHZ tPLZ tPZH tPZL SYMBOL tLR tLF FRFM VCRS PARAMETER Rise time Fall time Differential rise / fall time matching (tFR / tFF) Output signal crossover voltage Driver propagation delay (VO / VPO D+ / D- ; FSEO / VMO D+ / DDriver disable delay (OE D+ / D-) Driver enable delay (OE D+ / D-) CONDITIONS CL = 50 to 125pF, measured 10% to 90% (VOH-VOL); See Figure 6 CL = 50 to 125pF, measured 10% to 90% (VOH-VOL); See Figure 6 Excluding the first transition from idle state Excluding the first transition from idle state; See Figure 9 LOW-to-HIGH transition; See Figure 9 HIGH-to-LOW transition; See Figure 9 HIGH-to-OFF; See Figure 7 LOW-to-OFF; See Figure 7 OFF-to-HIGH; See Figure 7 OFF-to-LOW; See Figure 7 CONDITIONS CL = 200 to 600pF, measured 10% to 90% (VOH-VOL); See Figure 6 CL = 200 to 600pF, measured 10% to 90% (VOH-VOL); See Figure 6 Excluding the first transition from idle state Excluding the first transition from idle state; See Figure 9 CONDITIONS LOW-to-HIGH transition; See Figure 8 HIGH-to-LOW transition; See Figure 8 LOW-to-HIGH transition; See Figure 8 HIGH-to-LOW transition; See Figure 8 MIN 75 75 80 1.3 TYP MIN 4 4 100 1.65 18 18 15 15 15 15 MAX 300 300 125 2.0 TYP MAX 20 20 UNITS ns ns % V ns ns ns ns ns ns UNITS ns ns % V
Driver Characteristics & Timings (Low-speed mode only, SPEED=LOW) PARAMETER Rise time Fall time Differential rise / fall time matching (tFR / tFF) Output signal crossover voltage PARAMETER Driver propagation delay (D+ / D- RCV)
Receiver Timings (Full-speed and low-speed modes) SYMBOL tPLH(RCV) tPHL(RCV) tPLH(SE) tPHL(SE) MIN TYP MAX 15 15 18 18 UNITS ns ns ns ns Differential Receiver
Single-ended Receiver Driver propagation delay (D+ / D- VP / VM)
(c) 2004 California Micro Devices Corp. All rights reserved.
6
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
08/24/04
PRELIMINARY CM2400-02/03/04
Specifications (cont'd) Test Loads
Test Point 33 15pF
Test Point
50pF
Load for VP / VM and RCV delay measurements
Load for D+ and D- delay measurements (MAX and MIN Timing)
Test Point 33 200 50pF V V = VREG(3.3) for tPZL and tPLZ
V = 0 v for tPZH and tPHZ
DUT
Load for ENABLE and DISABLE delay measurements.
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
15k
DUT
DUT
www.calmicro.com
7
PRELIMINARY CM2400-02/03/04
Performance Information
CM2400-02/03/04 Typical DC Characteristics (nominal conditions unless specified otherwise)
1.00
300
VBUS CURRENT [A]
VCC CURRENT [A]
0.50
250
0.00
200
-0.50
150
-1.00 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 V CC VOLTAGE [V]
100 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 V BUS VOLTAGE [V]
Figure 3. VBUS Current in Idle Mode (SPND=LOW)
Figure 1. VCC Current in Idle Mode (SPND=LOW)
1.00
60.0
VBUS CURRENT [A]
VCC CURRENT [A]
0.50
55.0
0.00
50.0
-0.50
45.0
-1.00 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 VCC VOLTAGE [V]
40.0 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 V BUS VOLTAGE [V]
Figure 2. VCC Current in Suspend Mode (SPND=HIGH)
Figure 4. VBUS Current in Suspend Mode (SPND=HIGH)
(c) 2004 California Micro Devices Corp. All rights reserved.
8
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
08/24/04
PRELIMINARY CM2400-02/03/04
Performance Information (cont'd)
CM2400-02/03/04 Typical AC Characteristics (nominal conditions unless specified otherwise)
D+
D-
Figure 5. Rise and Fall Time Matching for Full-Speed Mode
D+
D-
Figure 6. Rise and Fall Time Matching for Low-Speed Mode
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
9
PRELIMINARY CM2400-02/03/04
Performance Information (cont'd)
CM2400 Timing Diagrams
3.3V
INPUT tFR, tLR VOH 90% 90% tFF, tLF
VCRS
VCRS
0V VOH
tPLH(RCV) tPLH(SE)
tPHL(RCV) tPHL(SE)
OUTPUT 10% VOL VOL 10%
0.9V
0.9V
Figure 7. Rise and Fall Timing
Figure 9. D+, D- to RCV, VP and VM Timing
1.65V 1.65V INPUT 0.9V 0.9V INPUT 0V VOH tPZH tPZL tPHZ tPLZ
-0.3V
0.9V
0.9V
0V tPLH(DRV) VOH tPHL(DRV)
OUTPUT
VCRS OUTPUT VCRS VCRS
+0.3V
VOL
VOL
Figure 8. OE to D+, D- Timing
Figure 10. VO/VPO, FSEO/VMO to D+, D- Timing
(c) 2004 California Micro Devices Corp. All rights reserved.
10 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
08/24/04
PRELIMINARY CM2400-02/03/04
Functional Description
The CM2400-02/03/04 USB Transceiver supports 3 different power supply configurations, which can be configured dynamically. Table 1 details the various configurations. In Normal Mode the internal regulator produces 3.3V from VBUS to power the internal drivers and receivers associated with the USB protocol.
VBUS Connected Connected Not Connected VCC Connected Not Connected Connected CONFIGURATION Normal Mode Disable Mode Sharing Mode
D- lines while in sharing mode. In this mode, VP and VM are driven high while RCV and USB_DET are driven low. In Disable and Sharing Mode, all input/output pins follow the states defined in Table 2.
Sharing Mode State VBUS < 3.6V Pulled Down Present High-Z (off) High-Z H L L High-Z Disable Mode State 4.1V to 5.5V 3.3V Out Not Present High-Z (off) High-Z Invalid Invalid Invalid High-Z
PIN VBUS VREG VCC VPU D+, DVP , VM RCV USB_DET Inputs
Table 1: Power Supply Connections There are three power supply configurations for the CM2400-02/03/04: Normal mode, Disable mode and Sharing mode. These three modes can be changed dynamically. Normal mode occurs when the VCC and VBUS inputs are both connected to a source. VBUS is tied to a 5V source for 5V operation. The internal regulator of the CM2400-02/03/04 provides 3.3V output on VREG. The VCC input is connected to an independent source that can range from 1.65V to 3.6V. When VCC is not connected and VBUS is connected, the device is in Disable mode. The D+ and D- pins are in tri-state and power consumption drops to a suspend state level. In Sharing mode, VCC is connected while VBUS is below 3.6V. The D+ and D- pins are in tri-state and the CM2400-02/03/04 allows external signals (3.6V) to share these two lines. The CM2400-02/03/04 is designed to draw almost zero current from the D+ and
Table 2: Pin States in Disable or Sharing Mode Table 3 lists the functions of the modes associated with suspend and OE pins. When Suspend is low and OE is high, signal levels on D+ and D- are determined by other USB devices and pull-up/down resistors. In Suspend Mode (SPND = HIGH) the differential receiver is inactive and output RCV is always LOW. Out of suspend signaling is detected via the single-ended receivers VP and VM. During suspend and while the output is still enabled (OE = LOW), D+ and D- lines are driven to their intended states.
SUSPEND L L H H
OE L H L H
D+ / DDriver & Receiver Active Receiving Driving High-Z
RCV Active Active Inactive RCV=L Inactive RCV=L
VP/VM Active Active Active Active
Function Normal driving mode. Differential receiver active Driver Tri-stated. Differential receiver active. Driving during 'suspend'. Differential receiver inactive. Low-power state.
Table 3: Function Selection.
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
11
PRELIMINARY CM2400-02/03/04
Functional Description (cont'd)
Detailed in Table 4 and Table 5 are the operating modes for the CM2400-02/03/04. The CM2400-02 features a fixed, single-ended input operating mode which is summarized in Table 4. The CM2400-03 features a differential-pair input operating mode which is summarized in Table 5. The CM2400-04 input mode is selectable via the MODE input. Table 4 and Table 5 summarize both operating modes for the CM2400-04. On the CM2400-02, the two driver inputs function as VO and FSE0 inputs. On the CM2400-03, the driver inputs function as VPO and VMO. On the CM2400-04, when the MODE input is HIGH, differential-pair input mode is selected and the two driver inputs function as VPO and VMO. When MODE is LOW, the single-ended input data interface mode is selected and the two driver inputs function as VO and FSE0.
VO (VPO) L L H H FSE0 (VMO) L H L H
Table 6 details the receiving function when OE is HIGH (driver disabled). RCV denotes the signal level on the output RCV just before an SE0 state occurs. This level is stable during the SE0 period.
VP L H L VM H L L
D+/DDifferential Logic '0' Differential Logic '1' SE0
RCV L H RCV*
* Denotes RCV is stable in last state before SE0 condition.
Table 6: Receiving Function (SPND = L) A regulator bypass option can be utilized by shorting VBUS to VREG and connecting to a 3.3v supply.
MODE L (single-ended)
Result Logic `0' SE0 Logic `1' SE0
Table 4: Single-ended Input Operating Mode, CM2400-02 and CM2400-04 in Single-ended Input Mode (OE = L)
VO (VPO) L L H H FSE0 (VMO) L H L H
MODE H (differential)
Result SE0 Logic `0' Logic `1' Undefined
Table 5: Differential-pair Input Operating Mode, CM2400-03 and CM2400-04 in Differential-pair Input Mode (OE = L)
(c) 2004 California Micro Devices Corp. All rights reserved.
12 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
08/24/04
PRELIMINARY CM2400-02/03/04
Mechanical Details
The CM2400-02/03/04 family is available in a 16-lead HBCC and 16-lead TSSOP packages.The mechanical details for these packages are presented below. HBCC-16 Mechanical Specifications Dimensions for the CM2400-02HB, CM2400-03HB and CM2400-04HB devices packaged in 16-pin HBCC packages are presented below. Mechanical Package Diagrams
TOP VIEW
13
D
9
A A1
PACKAGE DIMENSIONS
E
Package Pins Dimensions A A1 b1 b2 b3 D Dh E Eh e e1 e2 e3 e4 # per tube # per tape and reel Millimeters Min 0.05 0.25 0.30 0.30 2.90 1.45 2.90 1.75
HBCC-16 16 Inches Min Max 0.0315 0.0039 0.0138 0.0157 0.0157 0.1220 0.0610 0.1220
9 13 1 5
Max 0.80 0.10 0.35 0.40 0.40 3.10 1.55 3.10 1.85
SIDE VIEW
BOTTOM VIEW
e1 Dh e
0.0728 0.0197 TYP. 0.0984 TYP. 0.0984 TYP. 0.0965 TYP.
5 1 16
Detail C
0.50 TYP. 2.50 TYP. 2.50 TYP. 2.45 TYP. 2.45 TYP
e4
1/2 e4
e
Eh e2
0.0965 TYP.
1/2
120 pieces* 2500 pieces Controlling dimension: millimeters
e3 e3
Detail A
Detail B
CONTACT (PIN) DIMENSIONS
* This is an approximate number which may vary.
CF#0.20x45
b1 b1
Detail A
b2 b2
Detail B
b3 b3
Detail C
Dimensions for HBCC-16 Package
(c) 2004 California Micro Devices Corp. All rights reserved. 08/24/04
430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
13
PRELIMINARY CM2400-02/03/04
Mechanical Details (cont'd)
TSSOP-16 Mechanical Specifications Dimensions for the CM2400-02TS and CM2400-03TS devices packages are presented below. For complete information on the TSSOP-16 package, see the California Micro Devices TSSOP Package Information document. Mechanical Package Diagrams
TOP VIEW
D
16 15 14 13 12 11 10 9
PACKAGE DIMENSIONS
Package Pins Dimensions A A1 B C D E e H L # per tube # per tape and reel Millimeters Min -- 0.05 0.19 0.09 4.90 4.30 6.25 0.50 Max 1.10 0.15 0.30 0.20 5.10 4.50 6.50 0.70 Min -- 0.002 0.0075 0.0035 0.193 0.169 0.246 0.020 TSSOP 16 Inches Max 0.0433 0.006 0.0118 0.0079 0.201 0.177 0.256 0.028 END VIEW
C
SEATING PLANE 1 2 3 4 5 6 7 8
H
Pin 1 Marking
E
SIDE VIEW
A A1 B e
0.65 BSC
0.0256 BSC
Consult Factory 2500 pcs Controlling dimension: millimeters
L
Dimensions for the TSSOP-16 Package
(c) 2004 California Micro Devices Corp. All rights reserved.
14 430 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.calmicro.com
08/24/04

▲Up To Search▲

Price & Availability of CM2400-02TR

	To Download CM2400-02TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .